8/7/2023 0 Comments Dlink viewer![]() D-ViewCam then notifies you either by e-mail or an audio alert. When an event occurs, a notification is immediately sent to D-ViewCam Video Management Software. Start by connecting any of these devices to the I/O connector of a compatible D-Link network camera. Recorded files can be searched according to video type or selected within the user interface for playback, editing, or AVI /ASF file conversion.Įvent Action provides enhanced surveillance and security by detecting events from smoke detectors, magnetic door sensors, emergency buttons, cameras, card readers, or other I/O devices. The DCS-100 D-ViewCam Video Management Software offers scheduled, motion and manual recording options to meet specific user demands. Linux version 2.6.21 (gcc version 3.4.D-ViewCam Video Management Software DCS-100 # Transferring control to Linux (at address 803b8000). Image Type: MIPS Linux Kernel Image (lzma compressed) Icache: sets:256, ways:4, linesz:32 ,total:32768ĭcache: sets:128, ways:4, linesz:32 ,total:16384Ģ: Load system code then write to Flash via TFTP.ħ: Load Boot Loader code then write to Flash via Serial.ĩ: Load Boot Loader code then write to Flash via TFTP. *** Warning - bad CRC, using default environment Key4Str is Invalid key length(0) or Type(1)īr0: port 2(eth2) entering learning stateīr0: topology change detected, propagatingīr0: port 2(eth2) entering forwarding stateīr0: port 1(ra0) entering forwarding stateĬIFS VFS: cifs_mount failed w/return code = -6īusyBox v1.12.1 ( 15:01:26 CST) multi-call binaryįlash_protect ON: from 0xBF000000 to 0xBF021767įlash_protect ON: from 0xBF030000 to 0xBF030FFF Ke圓Str is Invalid key length(0) or Type(1) Key2Str is Invalid key length(0) or Type(1) Key1Str is Invalid key length(0) or Type(1) Usbcore: registered new interface driver snd-usb-audio Uvcvideo: UVC non compliance - GET_DEF(PROBE) not supported. Uvcvideo: Found UVC 1.00 device USB Camera Aoni (05a9:7885) Usb 1-1: configuration #1 chosen from 1 choice Usb 1-1: new high speed USB device using rt3xxx-ehci and address 2 Usbcore: registered new interface driver uvcvideo Ip_tables: (C) 2000-2006 Netfilter Core Team, Type=Restricted Coneįreeing unused kernel memory: 5356k freed Nf_conntrack version 0.5.0 (512 buckets, 4096 max) Usb usb2: configuration #1 chosen from 1 choiceĪdvanced Linux Sound Architecture Driver Version 1.0.14rc3 (Wed Mar 14 07:25:50 2007 UTC). Rt3xxx-ohci rt3xxx-ohci: irq 18, io mem 0x101c1000 Rt3xxx-ohci rt3xxx-ohci: new USB bus registered, assigned bus number 2 Rt3xxx-ohci rt3xxx-ohci: RT3xxx OHCI Controller Ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver Usb usb1: configuration #1 chosen from 1 choice Rt3xxx-ehci rt3xxx-ehci: USB 0.0 started, EHCI 1.00, driver Rt3xxx-ehci rt3xxx-ehci: irq 18, io mem 0x101c0000 Rt3xxx-ehci rt3xxx-ehci: new USB bus registered, assigned bus number 1 Rt3xxx-ehci rt3xxx-ehci: Ralink EHCI Host Controller PPP Deflate Compression module registered ***** Init RF/MAC data from flash memory ***** v2.0 256 rx/tx descriptors allocated, mtu = 1500! Ralink APSoC Ethernet Driver Initilization. RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize Serial: 8250/16550 driver $Revision: 1.7 $ 2 ports, IRQ sharing disabled HDLC line discipline: version $Revision: 1.1.1.1 $, maxframe=4096 Squashfs: version 3.2-r2 (5) Phillip Lougher TCP: Hash tables configured (established 2048 bind 2048) TCP bind hash table entries: 2048 (order: 1, 8192 bytes) TCP established hash table entries: 2048 (order: 2, 16384 bytes) IP route cache hash table entries: 1024 (order: 0, 4096 bytes) Time: MIPS clocksource has been installed. ![]() Usbcore: registered new device driver usb Usbcore: registered new interface driver hub Usbcore: registered new interface driver usbfs Memory: 52016k/65536k available (3126k kernel code, 13456k reserved, 445k data, 5356k init, 0k highmem)Ĭalibrating delay loop. Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) PID hash table entries: 256 (order: 8, 1024 bytes)ĭentry cache hash table entries: 8192 (order: 3, 32768 bytes) Synthesized TLB modify handler fastpath (31 instructions). Synthesized TLB store handler fastpath (32 instructions). Synthesized TLB load handler fastpath (32 instructions). Synthesized TLB refill handler (20 instructions). Primary data cache 16kB, 4-way, linesize 32 bytes. Primary instruction cache 32kB, physically tagged, 4-way, linesize 32 bytes. Kernel command line: console=ttyS1,57600n8 root=/dev/ram0 Initrd not found or empty - disabling initrd
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |